spinning and plugs.
Moderator: donal domeney
-
- SAI Sea Dog!
- Posts: 661
- Joined: Fri Sep 03, 2004 10:24 am
- Location: Belfast Northern Ireland
spinning and plugs.
Looking to the summer and need answered is there a site showing simple spinning traces.
Last year my lures were light and would not cover much ground. i waited the line so to get out but as a ex fluff chucker i would think this would affect the swim of the lure.
I use a carp rod as it goes like stink. Can anyone tell me how to get these light surface poppers out there.
Last year my lures were light and would not cover much ground. i waited the line so to get out but as a ex fluff chucker i would think this would affect the swim of the lure.
I use a carp rod as it goes like stink. Can anyone tell me how to get these light surface poppers out there.
Pookie,
What I do to achieve distance with a lightweight lure is this.... make an upside down bait clip on my main-line (a cut paper clip and some electrical wire sleeve) slide on a drilled bullit lead (half oz or 1oz whatever) tie a good quality swivel to the end of my main-line, then add my lure trace, that could be about 30" long, then before you cast out hook the lure onto the bait-clip (this should leave your lead at the bottom) the lure should unhook as it hits the water and the bullit lead should not give the lure that much problem as you work it back.
Hope you get what I mean.
Tom.
What I do to achieve distance with a lightweight lure is this.... make an upside down bait clip on my main-line (a cut paper clip and some electrical wire sleeve) slide on a drilled bullit lead (half oz or 1oz whatever) tie a good quality swivel to the end of my main-line, then add my lure trace, that could be about 30" long, then before you cast out hook the lure onto the bait-clip (this should leave your lead at the bottom) the lure should unhook as it hits the water and the bullit lead should not give the lure that much problem as you work it back.
Hope you get what I mean.
Tom.
-
- SAI Sea Dog!
- Posts: 890
- Joined: Wed Jun 29, 2005 5:36 pm
- Location: waterford
Use as small a diameter line as you can get away with. This will depend more on the ground that you are fishing than the size of the fish IMHO. I have landed bass over 10lb on 8lb line. Just set your drag properly and let the clutch do the work. Obviously you will have to up the breaking strain if the fish are lightly to dive into kelp etc.
-
- Moderator
- Posts: 733
- Joined: Tue Feb 17, 2004 5:36 pm
- Has thanked: 4 times
- Been thanked: 4 times
Hi
you could try 30lbs power pro casts like a bullet and should add some yards. also a carp rod might not be the best choice for casting light lures as the butt is the wrong shape and the rod will prob have quite a high test curve. a light tip action lure rod should help with distance. something like a 9 foot daiwa sensor would be an option and wont break the bank.
Adam
you could try 30lbs power pro casts like a bullet and should add some yards. also a carp rod might not be the best choice for casting light lures as the butt is the wrong shape and the rod will prob have quite a high test curve. a light tip action lure rod should help with distance. something like a 9 foot daiwa sensor would be an option and wont break the bank.
Adam
[img]http://s4.photobucket.com/albums/y116/adamsalbum79/th_tope3.jpg[/img]
-
- SAC Treasurer
- Posts: 4331
- Joined: Tue Jun 29, 2004 1:47 pm
- Location: Too far from Water
- Has thanked: 141 times
- Been thanked: 150 times
I use Braid... Power Pro like Adam. You could even go for a thinner diameter like 20lb. Don't do this if you haven't used braid before though Until you are used to it the lighter stuff might knot mid cast on you. Also as Adam mentioned go for a nice light setup. A Carp rod will be ok for heavier lures and plugs but if you want to cast the lighter stuff out you will need a well ballanced rod.
Kev
Kev
><º> ><º>
><º>
><º>
-
- SAI Bait Ball
- Posts: 118
- Joined: Wed Nov 24, 2004 1:07 pm
- Location: Kinsale
Hi Sam
I use the wire you can buy for making gripleads heated with a blowtorch to burn a hole through the ball. Then using the same wire pass it through the hole and form an eye with a swivel trapped in it on each end...
Attach one swivel to you mainline and the other to a flowing trace about a meter or so long. Tie your lure to the flowing trace.
Bouncy balls have a neutral buoyancy, works a treat for getting those light lures out a bit further, can be used for surface poppers or shallow divers j13's etc. Also helps to " bounce " the lure around rock obstacles
Andy
I use the wire you can buy for making gripleads heated with a blowtorch to burn a hole through the ball. Then using the same wire pass it through the hole and form an eye with a swivel trapped in it on each end...
Attach one swivel to you mainline and the other to a flowing trace about a meter or so long. Tie your lure to the flowing trace.
Bouncy balls have a neutral buoyancy, works a treat for getting those light lures out a bit further, can be used for surface poppers or shallow divers j13's etc. Also helps to " bounce " the lure around rock obstacles
Andy
-
- SAI Bait Ball
- Posts: 118
- Joined: Wed Nov 24, 2004 1:07 pm
- Location: Kinsale
Yup. You know the kind - usually transparent with a swirl of colour inside. Loaf them at a wall and they bounce for miles.
There is a school of thought that says the turbulence caused by the ball as it's dragged through the water mimics that of a wounded fish thrashing about - like ringing the dinner bell for any predatory species.
There is a school of thought that says the turbulence caused by the ball as it's dragged through the water mimics that of a wounded fish thrashing about - like ringing the dinner bell for any predatory species.